K+M Primer Pocket Correction Tool, Large Rifle
Large Rifle is set to 0.131" depth Designed with a drive shank to be used with your cordless screwdriver and/or either of K+M's handles. K+M's prim...
View full detailsThe proven way to control costs and produce precise ammunition is to prep and condition cases yourself. Preparing cartridge cases for hand-loading can be a time-consuming and labour intensive stage, but it can result in more accurate and consistent ammunition.
Case prep is important to the reloading process because the case acts as both a container for the powder and bullet and as a seal for the gun’s chamber. How well you prepare your cases will affect the accuracy and consistency of your ammunition.
Large Rifle is set to 0.131" depth Designed with a drive shank to be used with your cordless screwdriver and/or either of K+M's handles. K+M's prim...
View full detailsMade out of tool steel that gets heat treated and then ground. Replacement cutters for the K+M case neck turning tool are offered in a range of lea...
View full detailsIn cartridge manufacturing, the flash hole is "punched" into the brass. While this is the least expensive method, it has many shortcomings and inco...
View full detailsK+M Case Mouth Tapered Reamer - An improvement to a long standing superb case mouth chamfering tool with a newly designed handle that provides impr...
View full detailsThe K+M Case Holder Power Adapter is used to hold the cartridge whilst neck turning under the power of a cordless screwdriver or low speed drill. ...
View full detailsSmall Pistol & Small Rifle set to 0.122" depth Designed with a drive shank to be used with your cordless screwdriver and/or either of K+M's han...
View full detailsThis is the K+M Micro-Adjustable Case Neck Turner body (cutter/pilot not included.) Some reloaders like to have multiple tools set up and this is ...
View full detailsImproved ability to lock and unlock your case in the power adapter. Can be used with the K+M handle, cordless screw driver or drill. Slide the Pow...
View full detailsIt can be hard to hold the K&M Micro Adjustable Neck Turner due to its compact size, especially in higher volume use. The Ergo Holder is manufa...
View full detailsThe Pilot Jack is used to assist setting the pilot position on the K+M Neck Turning Tool to achieve the proper cut into the case shoulder. Installa...
View full detailsThe K+M Expand Mandrel Window Riser is a simple device that brings the case neck expanding above the press and allows for the full visual of the pr...
View full detailsVirgin/competition brass isn't quite ready to neck turn when you buy it. And the commercial die manufacturers have no set standards for the expande...
View full detailsVirgin/competition brass isn't quite ready to neck turn when you buy it. And the commercial die manufacturers have no set standards for the expande...
View full detailsThe K+M Press Adapter is used with K+M Expand mandrels. It threads directly into most standard reloading presses with 7/8-14 threads. It does not i...
View full detailsThis steel neck turning pilot is specifically for the K+M Neck Turning Tool. The use of a good lubricant is necessary to avoid galling brass during...
View full detailsThis steel neck turning pilot is specifically for the K+M Neck Turning Tool. The use of a good lubricant is necessary to avoid galling brass during...
View full detailsAn improvement to a long standing superb case mouth chamfering tool with a newly designed handle that provides improved depth stop fingers and a mu...
View full detailsThis aluminum handle is used with the K+M Power Adapter if you prefer to utilise the power case driver in manual mode while neck turning. This hand...
View full detailsVirgin/competition brass isn't quite ready to neck turn when you buy it. And the commercial die manufacturers have no set standards for the expande...
View full detailsVirgin/competition brass isn't quite ready to neck turn when you buy it. And the commercial die manufacturers have no set standards for the expande...
View full detailsVirgin/competition brass isn't quite ready to neck turn when you buy it. And the commercial die manufacturers have no set standards for the expande...
View full detailsThis finely ground carbide cutting pilot, designed for use with the K+M case neck turning body, has four cutting flutes used to remove the “doughnu...
View full detailsThis precision ground carbide cutting pilot, designed for use with the K+M case neck turning body, has four cutting flutes used to remove the “doug...
View full detailsIn cartridge manufacturing, the flash hole is "punched" into the brass. While this is the least expensive method, it has many shortcomings and inco...
View full details